DResearch TeleObserver MR3180 Скачать руководство пользователя страница 36

Страница: 36 / 66

DResearch – User Manual TeleObserver MR3180

2011-02-03

3.1.1.2

System :: Time

Caution: If you reset the time of the MR3140 unit backwards, and you then save the new
configuration, all the video footage which is now in the future according to the new time,
is automatically deleted!

Field

Description

Time Zone

Select a time zone from the listing.

The valid properties for that time zone are displayed in the fields below.

Time

Update time (while
sending the
configuration)

When the configuration is sent the time of the unit is synchronised with that of the

service PC.

External time sync

Regular synchronisation of the unit’s time with that of an external source.

Synchronization

Source

Here you select the external source for synchronising the device time.

For this the following conditions have to be fulfilled:

A GPS receiver is connected and configured.

The MR3180 is linked to the IBIS bus.

Synchronize time every
… Hour(s)

This is used to determine the synchronisation cycle.

Maximum difference …
Minute(s)

Enter here the maximum time deviation (in minutes) from the synchronisation

source.

If when compared, the time deviation is greater than this value then

synchronisation takes place. After that the device starts new.

Set your time zone and make

the settings for automatic time

synchronization in this dialog.

Содержание TeleObserver MR3180



































































Результаты поиска

Содержание TeleObserver MR3180

Отзывы:

Похожие инструкции для TeleObserver MR3180

Бренды по названию

Популярные бренды

DResearch TeleObserver MR3180, Руководство пользователя

Результаты поиска

Содержание TeleObserver MR3180

Отзывы:

Похожие инструкции для TeleObserver MR3180

Бренды по названию

Популярные бренды