manualshive.com logo in svg

Dräger Incubator 8000 IC, Инструкция по эксплуатации, Страница: 45 / 60

Поделиться
Скачать
Dräger Incubator 8000 IC Скачать руководство пользователя страница 45

Humidity control module

45

Fault, Cause, Remedy

Humidity control module

Fault

Cause

Remedy

Red H

2

O LED flashes.

Not enough water.

Refill water bottles.

Actual value display flashes.  

Fault in water heater.

Switch off humidity control module.

Intermittent tone commences.

Call DrägerService.

Red Sensor LED flashes.

Faulty sensor.

Switch off humidity control module.

Actual value display flashes.

Call DrägerService.

Continuous tone commences.

Climate sensor not 
properly connected.

Check connection.

Err flashes in actual value display.

Fault in humidifier.

Switch off humidifier.

Red Inop. LED is lit in main module.

Humidity control activated.

All other functions remain 

Continuous tone commences.

operational.
Call DrägerService.

Err is lit in actual value display.

Fault in humidifier.

All other functions remain

Humidity control switched off.

operational.
Call DrägerService.

% FEUCHTE/HUMID.

Control

%

H  O

2

Control

Sensor

%

Fault

Cause

Remedy

Height does not adjust when pedals

Thermal fuse triggered. 

Wait until motor has cooled. 

operated.

Incubator in end stop position.

No further adjustment possible.

Faulty lifting mechanism.

Call DrägerService.

Height adjustment

Содержание Incubator 8000 IC





























































Отзывы:

Нет отзывов