Dräger Incubator 8000 IC Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

Dräger Incubator 8000 IC Скачать руководство пользователя страница 36

Using phototherapy unit 800/8000/4000

Accessory
Follow relevant Instructions for Use.

●

Push trolley carrying phototherapy unit under
incubator.

●

Adjust height:
Minimum distance between bottom of phototherapy
unit and patient is:
0.4 m for Photo-Therapy 800/8000
0.3 m for Photo-Therapy 4000

If the working height or the height of the bed is

changed later, make sure that this minimum
clearance is still maintained.

●

Follow safety advice, see p.18.

Using "BabyLink Incubator" interface

(optional)

The "Babylink Incubator" interface provides incubator
data (actual values, set values, alarms) via a serial
interface.
At present, measured values can be displayed as trends
on the Babyguard 8000 Dräger Paediatric Monitor.
Other possible connections are the Dräger BabyScreen
or any Windows-PC which can run the ThermoView
program.

The interface protocol is included in the BabyLink
modification set (82 90 607).

Follow Instructions for Use for interface.

Operation
Phototherapy
Interface

36

mindestens 0,3 m

Fuse

7

at least 0.3 m

Example: Photo-Therapy 4000

«
...
34
35
36
37
38
...
»

Содержание Incubator 8000 IC





























































Отзывы:

Нет отзывов