Dräger Incubator 8000 IC Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 60

Dräger Incubator 8000 IC Скачать руководство пользователя страница 40

Before re-using for a patient

●

Re-assemble equipment, see "Stripping down",
p. 37-38.

●

Check that the seals for support bracket in the trough
are movable.

Fitting seals in the hand port openings:

●

Open hand port.

●

Insert seal marked with an "L" on nose, into left
opening.

●

Insert seal marked with an "R" on nose, into right
opening.

●

Position nose of seal on hinge.
Put sealing lip (thin edge of profile) to the outside.

●

Close hand port.

●

Testing Readiness for Operation, see p. 14.

Allow water heater to run dry:

– to disinfect heater

– to test that "water shortage" display is working

properly.

●

Switch on humidity control.

●

Allow heater to run until "water shortage" alarm is
triggered, see p. 30.

●

Switch off humidity control.

Do not put full bottles into bottle holder until just
before placing baby in incubator.

If using water container:
Do not refill water container until just before placing
baby in incubator.

●

Operate incubator in standby, p. 19

or

●

switch off incubator, cover with dust cover and store
ready for use.

Care
Before re-using

40

L

R

«
...
38
39
40
41
42
...
»

Содержание Incubator 8000 IC





























































Отзывы:

Нет отзывов