manualshive.com logo in svg

Dräger Incubator 8000 IC, Инструкция по эксплуатации, Страница: 42 / 60

Поделиться
Скачать
Dräger Incubator 8000 IC Скачать руководство пользователя страница 42

Air temperature control module

42

Fault, Cause, Remedy
Air temperature control module

Fault

Cause

Remedy

Red 

±

1.5 

°

C LED flashes. 

Air temperature in incubator is

Below set value:

Actual value display flashes.

deviating from set value by more

close openings in canopy and wait

intermittent tone commences.

than 

±

1.5 

°

C

for incubator to warm up.
Above set value:
remove additional heat sources
(lamps, radiators, sunlight). Wait until
incubator has cooled down.

Red 

TTTT

 LED flashes.

Air temperature above 38 

°

C

Remove additional heat sources

Actual value display flashes.

(Range of values set up to 37 

°

C)

(lamps, radiators, sunlight). Wait

intermittent tone commences.

Air temperature above 40 

°

C

for incubator to cool down.

(Range of values set up to 39 

°

C)

Press 

ƒ

 key when temperature has

dropped below the alarm limit for
temperature.

Red 

S

S

S

S

 LED flashes.

Fan not fitted.

Fit fan.

Actual value display flashes.
Continuous sound commences.

Fan not rotating or rotating too

Check that fan is connected to

slowly.

drive shaft properly.
Call DrägerService.

Red Sensor LED flashes.

Incubator temperature below 5 

°

C.

Wait for incubator to warm up fully.

Three dashes flash in centre of 
value display.  

Climate sensor disconnected.

Connect climate sensor.

Continuous tone commences.

Faulty air temperature sensor.

Call DrägerService.

Reset

Control

>37 °C

°C LUFT/AIR

±1,5 °C

Sensor

Control

>37 °C

°C

°C

Содержание Incubator 8000 IC





























































Отзывы:

Нет отзывов