manualshive.com logo in svg

Dräger Incubator 8000 IC, Инструкция по эксплуатации, Страница: 43 / 60

Поделиться
Скачать
Dräger Incubator 8000 IC Скачать руководство пользователя страница 43

Skin temperature control module (optional)

Fault

Cause

Remedy

Red 

±

0.5 

°

C LED flashes. 

Skin temperature deviating from

Below set value:

Actual value display flashes.

set value by more than 

±

0.5 

°

C.

check that sensor is properly fitted

Intermittent tone commences.

to patient.
Above set value:
measure core temperature of patient
and inform doctor responsible for
patient immediately.

Red Sensor LED flashes. 

Skin temperature sensor not

Check connection and put right, if

Three dashes flash in centre of 

properly connected.

necessary.

actual value display. 
Continuous tone commences.

Faulty skin temperature sensor.

Replace sensor.

Err flashes in actual value display.  

Fault in skin temperature control

Switch to air temperature control.

Red Inop. LED is lit in main module.

module while in operation.

Call DrägerService.

Continuous tone commences.

Err is lit in actual value display.

Fault in the skin temperature

Other modules continue to operate

control module; skin temperature

properly.

control switched off.

Call DrägerService.

Reference temperature of 36 

°

C

Temperature measuring unit not

Call DrägerService.

is outside tolerance of 

±

0.1 

°

C operating 

correctly.

when 

6

 key is pressed.

Three dashes are lit at the top in 

Temperature measured above 42 

°

C.

Cooling required.

actual value display.

Inform doctor responsible for 
patient immediately.

Three dashes are lit at bottom of 

Temperature measured below 30 

°

C.

Check that sensor is properly fitted

actual value display.

to patient.

Fault, Cause, Remedy

Skin temperature control module

43

Check

36 °C

±0,1

Control

°C HAUT/SKIN/PEAU/PIEL

± 0,5 °C

Sensor

Control

15.22

87.06

°C

°C

Содержание Incubator 8000 IC





























































Отзывы:

Нет отзывов