Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 146

background image

Page 73 of 145

www.opwglobal.com

9.2 Dry-Well Monitoring, Single-Wall Tank

Error! Reference source not found. represents a typical dry-well
monitoring layout for a single-wall tank. Monitoring wells are placed
around the perimeter of the tanks, and are dug as close as possible to
the tanks or product lines for optimal sensor response.

The  manhole  should  be  watertight  and  the  monitoring  well  should  be
at  least  2  feet  (61  cm)  deeper  than  the  bottom  of  the  tanks  to  be
monitored.  Either  2-inch  (5.1  cm)  or  4-inch  (10.2  cm)  well  casing
should be used.

To obtain an adequate sample area, the

perforated

section should be

a large part of the well casing’s length. Place a cap on the bottom of
the well casing to prevent dirt entry. Backfill dirt around the casing.

The vapor sensor monitors hydrocarbon vapors. A

liquid

sensor

should also be installed and placed lower than the vapor sensor to
detect any liquid buildup.

Though vapor sensors are

not

damaged by submersion in liquid, they

will  not  function  properly  until  removed  from  the  liquid  and  given
sufficient  time  to  dry.  The  sealed  liquid  sensor  is  protected  from
particles  such  as  dirt.  It  requires  no  particular  placement.  Any
combination of vapor and liquid sensors may be used.

Figure 9-2 Dry Well Monitoring, Single-Wall Tank

«
...
71
72
73
74
75
...
»

Содержание OPW SiteSentinel iSite



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для OPW SiteSentinel iSite

Бренд: DAVIS Страницы: 12

ORBISPHERE 3624

Бренд: Hach Ultra Страницы: 12

System SourceMeter 2601B

Бренд: Keithley Страницы: 13

Бренд: Keller-druck Страницы: 8

Бренд: Keithley Страницы: 343

Бренд: Keithley Страницы: 334

Бренд: La Crosse Technology Страницы: 2

Бренд: AEMC Страницы: 4

Бренд: Hanna Instruments Страницы: 28

Dusty Harp Pickup Series

Бренд: Dusty Strings Страницы: 5

Бренд: Power Measurement Страницы: 20

Бренд: Supertech agroline Страницы: 10

SoundAdvisor NMS045

Бренд: Larson Davis Страницы: 64

Бренд: Tenma Страницы: 52

Бренд: AEMC Страницы: 20

Бренд: A&D Страницы: 2

Бренд: Hammond Страницы: 106

Бренд: Xsensor Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды