Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 146

Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 26

Page 26 of 145

www.opwglobal.com

2.5 Tank Alert Modules

The  SiteSentinel®  iSite™  console  has  the  ability  to  trigger  an  overfill
alarm  using  the  Tank  Alert  module  (Figure  2-16).  This  module  has  an
audible  buzzer  and  an  external  light  to  warn  the  users  in  an  event  of
overfill or high-product alarm.

2.5.1 Tank Alert Wiring

The Tank Alert box will be wired into the internal output contacts of the
SiteSentinel® iSite™ console or OM4 relay. To connect wires inside the
Tank Alert box, follow these instructions (see Figure 2-15):

1.

Connect L1 line voltage to Terminal 4 in Tank Alert.

2.

Connect Neutral to Terminal 3 in Tank Alert.

3.

Connect Float 1 (Either Common or Normally Open) to Terminal
2 in Tank Alert.

4.

Connect Float 2 (Either Common or Normally Open) to Terminal
1 in Tank Alert.

5.

Connect cable from Float 1 to common on one of the internal
output contacts on the SiteSentinel® iSite™ main board.

6.

Connect cable from Float 2 to normally open of the internal
output contact on the SiteSentinel® iSite™ main board.

Figure 2-16 Tank Alert
Module

Figure 2-15 Tank Alert
Wiring Connections

«
...
24
25
26
27
28
...
»

Содержание OPW SiteSentinel iSite



















































































































































Отзывы:

Нет отзывов