Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 53

Страница: 53 / 146

Page 53 of 145

www.opwglobal.com

5.14 Dual-Float Dispenser Sump Sensor

Part No. 30-0232-D-10

This Dual-Float Sensor is the same as a Discriminating Dispenser Pan
Sensor, Part No. 30-0232-DH-10, but without Belcor

inside the

sensor. This makes it non-discriminating.

Maximum Wiring Length is the maximum length of cable to be used
to connect all sensors on an individual channel. This length includes
run of cable from VSmart to each sensor board in the string.

Without Belcor

inside sensor

Figure 5-15 Dual-Float Dispenser Sump Sensor

Dual-Float Dispenser Sump Sensor Specifications

Primary Use(s):

Dispenser Pan/Sump

Alternate Use(s):

STP Sumps

Detects:

Low Liquid, High Liquid, Fuel

Operating Temperature:

-40°F to 158°F (-40°C to +70°C)

Dimensions:

ength: 11.1” (28.2 cm), Diameter: 2.3” (5.8 cm)

Float Requirements:

Low: 1.5” (3.8 cm), High: 8” (20.3 cm)

Cable Requirements:

Belden #88760 or Alpha #55371

Maximum Wiring Length*:

1,000’ (305 m) field wiring

Multi-Drop Restriction:

16 per I.S. barrier channel (64 per barrier)

Connections:

Red = Power, Black = Signal, Shield = Ground

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Dover OPW SiteSentinel iSite, Руководство по установке, Страница: 53 / 146

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы: