Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 84

Страница: 84 / 146

Page 84 of 145

www.opwglobal.com

12.4 Waterproof Field Electrical Connections

It is VERY important to seal all probe and sensor connections in the
junction box to prevent corrosion of the wires.

1. Twist bare ends of wires together.

2. Secure the connection with a wire nut.

DO NOT use electrical tape on any connections! Tape prevents
proper sealing of the epoxy.

3. Waterproof

the

connections

with

the

supplied

SCOTCHCAST™  epoxy  resin  Insulating  Resin  Seal  packs.
They  are  provided  to  seal  the  electrical  connections  from
moisture  and  water  and  prevent  corrosion  of  the  connections.
Install one for each cable connection.

4. Bend the seal pack until the barrier between the two resins

weakens.

5. Force the clear and the black resins together and mix

thoroughly.

6. Move the mixture to one end of pack, then clip the other end.

7. Insert wires, wire nuts and the cable insulation end into the

seal pack.

8. Work the resin mixture into the ends of the wire nuts and

around both cable jackets.

•

Secure the seal pack around the cables with a tie wrap
and cable tie.

Figure 12-4 Epoxy Sealant Pack

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Dover OPW SiteSentinel iSite, Руководство по установке, Страница: 84 / 146

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы: