Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 38

Страница: 38 / 146

Page 38 of 145

www.opwglobal.com

4.5.4 Installing Adaptor, Float, Weight on the Probe

12. Carry the probe to the top of the tank in its rolled-up state.

13. Carry the floats and remaining installation components to

the top of the tank.

14. Cut the single tie wrap (Labeled #1) that is securing the tip

of the probe to the rest of the coil. This should provide

enough length to install the float and related hardware.

15. Assemble the remaining adaptor hardware that the float will

fit through and slide this adaptor assembly onto probe. Do

not apply thread sealant at this time.

16. Install the product float on the probe shaft with the magnet

towards the bottom of the probe.

17. Install the weight on the probe shaft with the recess toward

the bottom of the probe.

18. Install the weight-retaining pin through the hole in the tip of

the probe.

Figure 4-5 Adaptor, Float and Weight Installation

4.5.5 Installing the Flex Probe

19. Position the coiled probe over your shoulder so that the coil

is vertical with the float in front of you.

20. Feed the weight and floats into the tank opening. Be careful

not to scratch the probe shaft during the installation.

21. Cut the next tie wrap (Labeled #2) and continue feeding the

probe into the tank.

22. Continue cutting the tie wraps in order until the probe is all

the way in the tank.

23. Hand-tighten the probe into the still loose adaptor fittings.

Thread sealant is not required on the nylon probe bushing.

24. Install the rest of the adaptor to the tank using a minimal

amount of thread sealant. The assembly was done in this

manner to prevent the soft nylon probe bushing from being

cross-threaded.

Figure 4-6 Flex Probe
Installation

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Dover OPW SiteSentinel iSite, Руководство по установке, Страница: 38 / 146

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы: