Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 28

Страница: 28 / 146

Page 28 of 145

www.opwglobal.com

2.6 Internal Printer

An internal thermal printer option is available for the SiteSentinel®
iSite™ Console. The printer will install inside the cabinet. The printer will
be used for printing the various reports the SiteSentinel® iSite™ has
available.

2.6.1 Installation Procedure

Mount Printer Power Supply above the existing power supply.

Slide printer onto mounting bracket.

Mount printer and bracket in Si

teSentinel® iSite™ Console

fixing to four (4) pre-drilled holes.

Connect power cable to 3-connector power plug (CN1) on left-
hand side of power supply board.

Connect printer power cable to 6-connector plug (CN2) on right-
hand side of board.

Connect printer ribbon cable to J22 on right-hand side of main
communication board.

Figure 2-19 Internal Printer

Figure 2-19 Main Board Printer Connections

CN2

CN1

J22

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Dover OPW SiteSentinel iSite, Руководство по установке, Страница: 28 / 146

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы: