Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 37

Страница: 37 / 146

Page 37 of 145

www.opwglobal.com

4.5 Flex Probe Installation

Proper  operation  of  the  SiteSentinel®  iSite™  system  using  the    flex
probe  depends  on  the  correct  sizing  of  the  probe.  If  the  probe  is  too
long,  it  will  touch  the  bottom  of  the  tank  and  bow,  causing  either
inaccurate  or  loss  of  readings.  If  it  is  too  short,  product  measurement
range will be compromised.

Each Flex Probe is custom made to fit a particular tank. They are not
returnable if an error is made in determining the correct length.

4.5.1 Probe Length Determination

1. The flex probe mounts to the tank with a ¾-inch NPT male

thread. Obtain the proper fittings to adapt the tank opening

to a ¾-

inch NPT female thread. Do not use the tank’s vent

opening to install the flex probe.

2. Temporarily install this hardware in the tank opening.

3. Using a plumb bob or measuring tape measure the distance

(in inches) from the top of the ¾-inch NPT flange to the

bottom of the tank. Save this measurement, which will be

Total Height (TH).

4. Flex probes are ordered by overall length (OAL). Overall

length is the distance from the top of the ¾-inch (19.1 mm)

NPT wiring bushing to the tip of the probe. OAL (inches) =

1.5 + (TH x .993)

•

If cable runs to 750 feet (229 m) use Belden #88761

•

If cable runs to 1,000 feet (305 m) use Belden #8760,
#88760 or #8761

Some electrical codes require intrinsically safe wiring to have a blue

jacket.

4.5.2 Installation Preparations

5. Measure the product level in the tank. Keep tank out of

service to prevent product level from changing.

6. Make note of the probe information found on the probe

serial number tag.

7. Locate standard plumbing fittings that will adapt your tank

opening to the ¾-inch NPT required for the probe.

8. Mount all of the pieces of this adaptor that floats will fit

through to the tank opening using a minimal amount of

thread sealant. Wipe any excess sealant from the inside of

the fittings to prevent any from getting on the probe shaft

during installation.

4.5.3 Installation Procedure

9. Run one data cable for each probe. No splices are allowed

between probe junction box and console. Multiple TLM flex-

probe cables are allowed in one conduit. Use masking tape

or labels to mark TANK # on each cable at the console.

10. Leave 16-inches (40.6 cm) in length of cable inside the

probe junction box for connection.

11. Install fiber dam and sealing compound in all TLM vapor

seal-off fittings.

Figure 4-4 Probe Installation

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Похожие инструкции для OPW SiteSentinel iSite

Бренды по названию

Популярные бренды

Dover OPW SiteSentinel iSite, Руководство по установке

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Похожие инструкции для OPW SiteSentinel iSite

Бренды по названию

Популярные бренды