Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 64

Страница: 64 / 146

Page 64 of 145

www.opwglobal.com

6.1.2 Installation

1. Remove all pressure from the product piping.

2. Remove the current mechanical leak detector.

CAUTION: Be sure to prevent any debris or scaling from entering
system through the leak detector opening.

3. Use the fuel-absorbent cloths to soak up fuel within the

work area and around the dry pipe threads.

4. Use an emery cloth to remove any burrs in the packer of

the VLLD sensor seat.

5. Plug the line test port.

NOTE: Apply fuel-approved thread sealant (not thread tape) to
plug.

6. Install the sensor in the existing submersible pump line

leak detector port. Take care not to damage O-ring seal.
a. Apply proper thread sealant to the sensor threads.

b. Install into test port and tighten by hand.

c. Using the proper wrench, tighten the sensor using the

flats below the cap or the hex on top of the sensor.

Tighten only enough to prevent leakage. Do not over

tighten!

7. Connect the sensor wires to the field wires in the junction

box using the supplied wire nuts. See figure 6.5.

8. Seal the electrical connections with the epoxy seal packs.

9. Clean the area and power the pump.

Figure 6-2 Soak-up Fuel

Figure 6-3 Apply Thread Sealant

Figure 6-4 Tighten Sensor

Figure 6-5 VLLD Wiring Connections

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Похожие инструкции для OPW SiteSentinel iSite

Бренды по названию

Популярные бренды

Dover OPW SiteSentinel iSite, Руководство по установке

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Похожие инструкции для OPW SiteSentinel iSite

Бренды по названию

Популярные бренды