Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 115

Страница: 115 / 146

Page 115 of 145

www.opwglobal.com

Appendix F- Icon Glossary (cont.)

Communication Ports

Port

Available

Unavailable

Icon

Available

Unavailable

Displayed when the port is
available for selection. Icon
is outlined in blue.

Displayed when the item is
currently unavailable. Icon is
completely grayed.

Displayed when the port is
available for selection. Icon
is outlined in blue.

Displayed when the item is
currently unavailable. Icon is
completely grayed.

Other Sensors:

Occurs on sensors that do
not have a specific
association, like float-switch
sensors.

Back/Left:

Used to go back to the
previous screen or scroll left.

Modem:

Used for communication to
and from console via internal
modems (Fax or Remote
Dial-In)

Next/Right:

Used to go to the next page
or scroll to the right.

Serial:

Used for serial
communication for POS and
other interfaces.

Up:

Used to scroll up.

USB:

Used to communicate to
external devices, such as
thumb drives, mouse or
keyboard.

Down:

Used to scroll down.

Wireless:

Used for communication
between console and
modules.

Contact:

Used to determine if contact
is available or unavailable.

LAN/WAN:

Used for remote access to
the system or to
communicate with VSmart
Modules.

Hose:

Used to determine if a hose
is available or unavailable.

Содержание OPW SiteSentinel iSite



















































































































































Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы:

Dover OPW SiteSentinel iSite, Руководство по установке, Страница: 115 / 146

Результаты поиска

Содержание OPW SiteSentinel iSite

Отзывы: