Dover OPW SiteSentinel iSite Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 146

background image

Page 50 of 145

www.opwglobal.com

5.11 Interstitial Hydrocarbon Liquid Sensor with

Water Indicator

Part No. 30-0234-HW-01

The   Interstitial   Hydrocarbon    Liquid/Water   Sensor   (Figure    5-11)
is  designed  for  use  in  the  interstitial  area  of  a  fiberglass  double-walled
tank.  The  hydrocarbon  liquid/water  sensor  contains  a  carbon/polymer
material  that  changes  its  resistance  when  exposed  to  liquid
hydrocarbons.  Additionally,  it  contains  a  conductive  strip  to  detect  the
presence  of  water,  providing  the  ability  to  discriminate  between
hydrocarbon  liquid  and  water.  In  the  event  of  a  break  in  the  cable,  the
system will activate the alarm.

*Maximum Wiring Length is the maximum length of cable to be used
to connect all sensors on an individual channel. This length includes
run of cable from VSmart to each sensor board in the string.

Figure 5-11 Interstitial
Hydrocarbon Liquid
Sensor with Water
Indicator

Interstitial Hydrocarbon Liquid/Water Sensor Specifications

Detects:

Liquid hydrocarbons/water

Operating Temperature:

-40°F to 158°F (-40°C to +70°C)

Dimensions:

Length: 13.8” (35 cm), Width: 1.0” (2.5 cm)

Nominal Resistance:

Uncontaminated: 1000-3000 ohms
Contaminated: 10,000-200,000 ohms

Cable Requirements:

Belden #88760 or Alpha #55371

Maximum Wiring Length*:

1,000’ (305 m) field wiring

Multi-Drop Restriction:

16 per I.S. barrier channel 64 per barrier)

Connections

Red = Power, Black = Signal, Shield: = Ground

«
...
48
49
50
51
52
...
»

Содержание OPW SiteSentinel iSite



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для OPW SiteSentinel iSite

Бренд: TaiDoc Страницы: 31

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Sensia Страницы: 139

Бренд: York Страницы: 2

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

Бренд: Rodstation Страницы: 28

QI-POWER-485-300

Бренд: QEED Страницы: 2

DUSTHUNTER C200

Бренд: SICK Страницы: 126

Бренд: Hameg Страницы: 40

Бренд: A-CUBE Страницы: 25

Бренд: POSEIDON Страницы: 21

Бренд: Isspro Страницы: 2

Бренд: R&S Страницы: 60

PowerGuide 4400

Бренд: Dranetz Страницы: 277

Бренд: Televes Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды