8
THANK YOU
for choosing this DÖRR quality product.
Please read the instruction manual and safety hints carefully before fi rst use. Keep this
instruction manual together with the device for future use. If other people use this device,
make this instruction manual available. This instruction manual is part of the device and
must be supplied with the device in case of sale.
DÖRR is not liable for damages caused by improper use or the failure to observe the
instruction manual and safety hints.
CAUTION! Please note the following important hints before fi rst use:
1. For initial use and/or after storage of up to 1 year and longer, please do not release
more than 3 flashes per minute for the first approx. 30 flash releases!
2. Not suitable for flash sequences of 10 or more releases in quick succession. After
flash sequences, cool down the studio flash for at least 2 minutes in order to avoid
damages to the flash condenser.
3. The modelling light is only designed to illuminate the object while the camera set-
tings are made. It is not suited as a permanent light since it produces high tempera-
tures which can harm flash accessories. In combination with conical snoots, soft-
boxes, honey combs or other flash accessories the modelling light must not be used
for more than 10 minutes.
GB
INSTRUCTION MANUAL
EcoLine II
Studio Flash
01 |
SAFETY HINTS
•
The flash tube and the modelling light produce high temperatures, which is also trans-
ferred to the reflector.
While operation never touch the ignition wire, the flash tube, the
modelling light and the reflector – risk of burns and of electric shock!
•
Cool down the studio flash before making any installations or before you store it.
•
Do not trigger the studio flash directly in front of the eyes of humans or animals.
This
may cause an irreversible damage to the retina.
Keep a minimum distance of 2,5m and
make sure that people or animals do not look directly into the studio flash.
•
Do not touch the modelling light and the flash tube with bare hands. Greasy finger-
prints may cause the bursting of the lamps during operation!
Wear thin gloves e.g.
made of cotton or microfiber or use a cloth for inserting or replacing the lamps.
•
Make sure that the studio flash is mounted stable and secure and cannot tip over.
Risk
of fire!
Take care that that nobody stumbles over the cable connections.
•
Keep away from flammable materials.
•
Only for the illumination for photographic purposes. Not suited for permanent room
lightning.
•
If the unit has been triggered continuously for e.g. 10 times or more in a short period,
please interrupt the operation for about 2 minutes in order to avoid overheating.
•
If you notice a smell of burning, switch off the studio flash immediately at the main
switch and disconnect from power.
Risk of fire!
Please contact your dealer.
•
Protect the device from rain, moisture, direct sunlight and extreme temperatures.
•
Do not touch or operate the device with wet hands or when standing on wet floor.
•
Ensure sufficient ventilation during operation. Never cover the ventilation slots.
•
Turn off the device after use and disconnect from power source.
•
Do not use an extension cord.
•
Protect the device against impacts. Do not use the device if it has been dropped. In this
case a qualified electrician should inspect the device before you use it again.
•
Inside the studio flash may occur high voltage. Do not attempt to repair the device by
yourself.
Risk of electric shock!
When service or repair is required, contact qualified
service personnel.
•
Do not use the device nearby mobile phones and devices that generate strong electro-
magnetic fields (e.g. electric engines).
•
People with physical or cognitive disabilities should use the device with supervision.
•
People with cardiac pacemakers, defibrillators or any other electrical implants should
maintain a minimum distance of 30 cm, as the device generates magnetic fields.
•
This device is not a toy. To prevent accidents and suffocation keep the device, the
accessories and the packing materials away from children and pets.
•
Protect the device against dirt. Never use aggressive cleansing agents or benzine to
clean the device. We recommend a soft, slightly damp microfiber cloth to clean the
outer parts of the device.
Make sure to take off the device from power before cleaning!
•
Store the device in a dust-free, dry and cool place.
•
If the device is defective or without any further use, dispose of the device according to
the Waste Electrical and Electronic Equipment Directive WEEE. For further information,
please contact your local authorities.
Содержание 371190
Страница 2: ......
