Dormakaba ED50, Руководство по установке

Страница: 2 / 116

2 ED50 01-2020 DL4615-001
dormakaba ED50 Installation Instructions – Fine cover Table of Contents
Table of contents 2
1 General information 4
1.1 General information 4
2 Product description 5
2.1 Product description 5
2.2 Handing of door 5
3 Safety information 6
4 ED50 Product overview 7
4.1 ED50 push arm system 7
4.2 ED50 pull arm system 7
4.3 RH door configurations 8
4.4 LH door configurations 9
4.5 Double door configurations 10
4.6 Double egress door configurations 11
4.5 ED50 operator 12
4.6 ED50 operator component views 13
4.7 Axle extensions 14
4.8 Arm configurations 14
4.9 Push arm door stop - option 15
4.10 Optional full width cover kits DK3401 15
5 Accessory kit, axle extension kits 16
5.1 ED50 low energy accessory kit 16
5.2 Double door ED50 operator connection
cables 17
5.3 Optional key switch panels 17
6 Technical data 18
6.1 ED50 Technical data 18
6.2 Operating specifications 19
7 Operational mode overview 19
7.1 ED50 door closer modes 19
7.2 Low energy product 19
8 User interface 20
8.1 Overview 20
8.2 4 button keypad and display 20
8.3 Program switches 21
8.4 Operator status LEDs 21
9 System accessories 22
9.1 System accessory electrical connections 22
9.2 System accessories 22
9.3 ED50 terminal board interfaces 23
10 ED50 door signage 24
10.1 Low energy operator 24
10.2 Door signage, low energy swing door 24
10.3 Door signage, low energy double doors 25
10.4 Safety label, low energy swing doors 26
11 Recommended tools and torque chart 27
11.1 Recommended tools 27
11.2 Standard tightening torque 27
11.3 Drill bits 27
Table of contents
12 ED50 operator installation 28
12.1 Installation preparation 28
12.2 Installation templates, single door 29
12.3 Installation templates, double doors 38
12.4 Remove mounting plate from ED50
operator 42
12.5 Customer 115 Vac connection to
mounting plate terminal block 43
12.6 Mounting plate attachment to jamb or
wall 45
12.7 Connect customer 115 Vac to mounting
plate terminal block 46
12.8 Route accessory wiring to mounting plate 46
12.9 Remove protective film strips from
operator 47
12.10 Install ED50 operator onto mounting plate 47
13 Push arm installation 48
13.1 Push arm installation templates 48
13.2 Push arm installation 48
13.6 Set ED50 operator spring tension 51
14 Arm with track mount installation 52
14.1 Arm with track installation 52
14.2 Splined arm and track assemblies 52
14.3 Splined arm and track hardware 52
14.4 Slide shoe assembly 53
14.5 Install hardware into track 53
14.6 Fasten track assembly to door 54
14.7 Arm assembly 55
14.8 Arm assembly with CPD lever 55
14.9 Fasten arm to ED50 operator 56
15 Measure door width, reveal depth 58
15.1 Door width parameter Tb 58
15.2 Tb parameter values 58
15.3 Reveal depth parameter rd 59
15.4 rd parameter values 59
16 Braking circuit plug 60
16.1 Braking circuit plug position 60
17 Power fail closing speed 61
17.1 Set power fail closing speed 61