Installation Instructions for Wi-Q Technology™ EXQ Exit Hardware Trim
BEST
a Product Group of dormakaba USA Inc.
12
Installing the exit hardware and trim
10
Route wire harnesses and position
escutcheon
1 From the outside of the door, feed the antenna wire
and battery connector (with relay shunt) through the
battery bracket/harness hole as shown in Figure 18.
Caution 1:
When routing the connectors, make
sure the harnesses are not routed across any
sharp edges or over any surface that could
damage their sleeving or wire insulation.
Caution 2:
Do not strain the wire harness either by
pulling too hard on it or by dangling the
escutcheon from it.
2 Route the sensor harness through the door (same hole
as the door sensing wires).
3 Rest the escutcheon on the door by inserting the trim
studs into the mounting holes.
11
Install cylinder (Precision devices)
For rim and vertical rod exit device installations (rim
cylinder)
1 To determine the correct spindle length, try the cylin-
der in the door while holding the escutcheon and lock
stile case in place.
Then break off the spindle at the groove where it will
engage correctly with the latching mechanism.
Break off the mounting screws at the groove where
they will secure the clamp plate to the cylinder.
2 Insert the cylinder through the cylinder opening in the
escutcheon and into the door as shown in Figure 19.
3 Orient the cylinder and clamp plate as shown in
Figure 20. From the inside of the door, secure the cyl-
inder using the clamp plate and mounting screws.
Figure 18 Feeding the wires through the door
Escutcheon
Outside of door
Battery
connector
Battery
bracket/
harness hole
Relay shunt
(Future use)
Antenna
wire
Sensor harness
Door sensing
switch and
wires
Rim
cylinder
Figure 19 Installing the cylinder
Escutcheon
Outside of door
Installation Instructions for Wi-Q Technology™ EXQ Exit Hardware Trim
BEST
a Product Group of dormakaba USA Inc.
11
Installation Instructions for Wi-Q Technology™ EXQ Exit Hardware Trim
Installing the exit hardware and trim
For Von Duprin vertical rod devices and rim without
RQE
4 Re-route the sensor harness as shown in Figure 16.
5 Reattach the backplate ensuring that the springs are
properly seated and wires are not pinched.
6 Reapply the gasket.
9
Install cylinder (Von Duprin only)
1 To determine the correct spindle length, try the cylin-
der in the door while holding the escutcheon and lock
stile case in place.
Then break off the spindle at the groove where it will
engage correctly with the latching mechanism.
If necessary break off the mounting screws as shown in
Figure 17.
2 From the front of the escutcheon, insert the cylinder
into the cylinder opening.
3 Holding the cylinder in position in the escutcheon,
insert the cylinder mounting sleeve through the back
of the escutcheon, over the cylinder.
4 Orient the cylinder and clamp plate as shown in
Figure 17. From the back of the escutcheon, secure the
cylinder and mounting sleeve using the clamp plate
and mounting screws.
Figure 16 Re-routing the sensor harness for Von Duprin
vertical rod and rim without RQE exit devices
Route
sensor
harness
here
Sensor
harness
Backplate
Figure 17 Installing the cylinder for Von Duprin
rim and rod exit devices
Rim
cylinder
Screws
Spindle
Clamp
plate
Break off the
screws here.
Orient the
curve toward
the cylinder.
Mounting
sleeve
Escutcheon
Содержание BEST Wi-Q ONGUARD
