Ditch Witch SK750 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 83

background image

Specifications - 75

SK750/SK755 Operator’s Manual

SK750/SK755 Basic Unit

CMW

Specifications are called out according to SAE recommended practices. Specifications are general and subject to change without
notice. If exact measurements are required, equipment should be weighed and measured. Due to selected options, delivered
equipment may not necessarily match that shown.

Bucket rollback angle, ground level

25°

25°

Bucket rollback angle, full height

90°

90°

Dump angle, standard bucket at max dump height

35°

35°

Bucket width, max

44 in

1120 mm

Bucket width, min

36 in

915 mm

Swing radius, max, with standard bucket

65 in

1650 mm

Swing radius, no attachment

44 in

1120 mm

Rear overhang, max

29 in

735 mm

Performance

U.S.

Metric

Ground drive speed, forward and reverse

4.7 mph

7.6 km/h

Ground pressure, 7” (180 mm) tracks *

4.8 psi

0.33 bar

Ground pressure, 9” (230 mm) tracks *

3.8 psi

0.26 bar

Tipping capacity

The rated operating capacity for this machine was determined using a standard bucket in
the drive position with center of gravity 7 in (18 cm) from the mounting plate. Depending
on the attachment, the actual operating capacity of the attachment may vary.

2285 lb

1039 kg

Operating capacity (35% of tipping capacity)

800 lb

364 kg

Machine weight (no attachment, fluids full)

2890 lb

1314 kg

* Includes machine weight, 175-lb (80-kg) bucket, 165-lb (75-kg) operator

Battery

SAE reserve capacity 110 min, SAE cold crank @ 0°F (-18°C) 800 amp, 12V electrical system

Fluid Capacities

U.S.

Metric

Fuel tank

10.5 gal

40 L

Engine oil, with filter

4.2 qt

4 L

Hydraulic reservoir

9.2 gal

35 L

Dimensions

U.S.

Metric

«
...
73
74
75
76
77
...
»

Содержание SK750




















































































Отзывы:

Нет отзывов

Похожие инструкции для SK750

Бренд: Komatsu Utility Страницы: 258

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды