Ditch Witch SK750 Скачать руководство пользователя страница 24

Страница: 24 / 83

SK750/SK755 Operator’s Manual

Controls - 24

Gauges and Indicators

CMW

Ignition switch

To start engine, insert key and
turn clockwise.

To stop engine, turn key
counterclockwise.

IMPORTANT:

•

If engine does not start or stalls,
turn key to STOP and then
restart.

•

Do not allow starter motor to run
continuously for more than 20
seconds.

Hourmeter

Displays engine operating
time.

Use these times to schedule service.

Engine coolant
temperature indicator

Lights and alarm sounds
when engine coolant
temperature is too high.

1. Stop operation, set throttle to low
idle, and allow engine to cool.

2. Stop engine.

3. Check coolant level.

Glow plug indicator

Lights when ignition switch is
on and glow plug button is
pressed.

10. Fuel tank sight window

Shows level of fuel in tank.

NOTICE:

Use low sulfur or ultra low

sulfur fuel only.

Item

Description

Notes

Содержание SK750




















































































Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды

Ditch Witch SK750, Руководство оператора

Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды