Ditch Witch SK750 Скачать руководство пользователя страница 17

Страница: 17 / 83

Safety - 17

SK750/SK755 Operator’s Manual

Safety Alerts

CMW

Tipover possible. Machine can tip over and crush you.

• Always operate with load end uphill.

• Always carry load low. High load can cause tipping, loss of load or loss of

visibility.

• Never jerk control levers. Use a steady even motion.

• See page 75 for tip capacity.

Flying objects may cause injury. Wear hard hat and safety glasses.

Hot parts may cause burns. Do not touch until cool.

Exposure to high noise levels may cause hearing loss. Wear hearing

protection.

Fall possible. Slips or trips may result in injury. Keep area clean.

Battery acid may cause burns. Avoid contact.

Improper handling or use of chemicals may result in illness, injury, or

equipment damage. Follow instructions on labels and in material safety data sheets
(MSDS).

Содержание SK750




















































































Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды

Ditch Witch SK750, Руководство оператора

Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды