manualshive.com logo in svg

Ditch Witch SK750, Руководство оператора, Страница: 58 / 83

Поделиться
Скачать
Ditch Witch SK750 Скачать руководство пользователя страница 58

SK750/SK755 Operator’s Manual

Service - 58

Startup/10 Hour

CMW

Startup/10 Hour  

Check Engine Oil Level 

Check engine oil level at dipstick opening (1) at 
startup and every 10 hours. Oil level should be at 
top of marking. If low, add DEO at fill (2). Check 
with unit on level surface and at least 15 minutes 
after stopping engine.

Check Engine Air Filter Service 
Indicator 

Check air filter service indicator (shown) at startup 
and every 10 hours and change filter as needed. 
See “Change Air Filter” on page 69. 

Task

Notes

Check engine oil level

DEO

Check engine air filter service indicator

Check engine coolant level

DEAC

Grease front track idler rollers

MPG

Check hydraulic fluid level

THF

Check brake operation

Check track tension

Check hydraulic hoses 

IMPORTANT: 

 Use oil specified in 

“Engine Oil Temperature Chart” on 
page 56.

t35om009w.eps

1

2

t35om010w.eps

Содержание SK750




















































































Отзывы:

Нет отзывов