Ditch Witch SK750 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 83

background image

SK750/SK755 Operator’s Manual

Service - 60

Startup/10 Hour

CMW

Check Track Tension

Check track tension at startup and every 10
hours and adjust as needed. Track is correctly
tensioned when measurement between track and
straight edges (2) is 1/2 in (13 mm).

To adjust:

1.

Park machine on smooth flat surface.

2.

Lay straight edge on top of track, spanning
from sprocket to front idler roller.

3.

Clean track cylinder zerk (1). Pump MPG into
zerk until distance between track and straight
edge (2) is 1/2” (13 mm).

4.

Test

: Drive forward one track length and

check tension again.

•

If tension is too loose, repeat step 3
above.

•

If tension is too tight, loosen fitting on
grease cylinder and allow a small
amount of grease to discharge from
cylinder. Tighten fitting and test again.

Check Coolant Level

Check coolant level, with engine cool, at overflow
bottle at startup and every 10 hours. Maintain
coolant level at halfway point on bottle. If low, add
approved coolant.

IMPORTANT:

See page 56 for information on

approved coolants.

t35om033w.eps

1

2

t35om015w.eps

«
...
58
59
60
61
62
...
»

Содержание SK750




















































































Отзывы:

Нет отзывов

Похожие инструкции для SK750

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды