manualshive.com logo in svg

Ditch Witch SK750, Руководство оператора, Страница: 19 / 83

Поделиться
Скачать
Ditch Witch SK750 Скачать руководство пользователя страница 19

Safety - 19

SK750/SK755 Operator’s Manual

Emergency Procedures

CMW

If an Electric Line is Damaged

If you suspect an electric line has been damaged and you are 

on platform

, DO NOT MOVE. Remain on 

platform and take the following actions. The order and degree of action will depend upon the situation.

•

Warn people nearby that an electric strike has occurred. Instruct them to leave the area and contact 
utility.

•

Raise attachments and drive from immediate area.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

If you suspect an electric line has been damaged and you are 

off platform

, DO NOT TOUCH UNIT. Take 

the following actions. The order and degree of action will depend upon the situation.

•

LEAVE AREA. The ground surface may be electrified, so take small steps with feet close together to 
reduce the hazard of being shocked from one foot to the other. For more information, contact your 
Ditch Witch dealer.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

If a Gas Line is Damaged

If you suspect a gas line has been damaged, take the following actions. The order and degree of action will 
depend on the situation.

•

Immediately shut off engine(s), if this can be done safely and quickly.

•

Remove any ignition source(s), if this can be done safely and quickly.

•

Warn others that a gas line has been cut and that they should leave the area.

•

Leave jobsite as quickly as possible.

•

Immediately call your local emergency phone number and utility company.

•

If jobsite is along street, stop traffic from driving near jobsite.

•

Do not return to jobsite until given permission by emergency personnel and utility company.

Содержание SK750




















































































Отзывы:

Нет отзывов