Ditch Witch SK750 Скачать руководство пользователя страница 27

Страница: 27 / 83

Controls - 27

SK750/SK755 Operator’s Manual

Controls

CMW

Parking brake lever

To engage, rotate lever
counterclockwise.

To disengage, rotate lever
clockwise.

Lift arm control

To move lift arms down, push.

To float, push forward to end.

To move lift arms up, pull.

To curl attachment up, move
to left.

To curl attachment down,
move to right.

IMPORTANT:

Exercise caution when

lifting loads. See page 75 for
operating capacities.

Attachment drive
control

To engage attachment drive
in reverse, lift lever lock and
push forward.

To engage attachment drive
in forward, lift lever lock and
pull back.

IMPORTANT:

•

Lever lock engages when control
is in neutral.

•

Use foot pedal to hold attachment
control in the on position when
hands are busy operating lift arm
or track drive controls.

Attachment drive foot
control

To hold attachment drive in
engaged position (forward or
reverse), lift lever lock, move
lever in desired direction, and
press pedal.

To return attachment drive
control to neutral, release
pedal.

IMPORTANT:

Use foot pedal to hold

attachment control in the on position
when hands are busy operating lift
arm or track drive controls.

Item

Description

Notes

c00ic662w.eps

Содержание SK750




















































































Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды

Ditch Witch SK750, Руководство оператора

Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды