Ditch Witch SK750 Скачать руководство пользователя страница 18

Страница: 18 / 83

SK750/SK755 Operator’s Manual

Safety - 18

Emergency Procedures

CMW

Emergency Procedures

Before operating any equipment, review emergency procedures and check that all safety precautions have
been taken.

Electric Strike Description

When working near electric cables, remember the following:

•

Electricity follows all paths to ground, not just path of least resistance.

•

Pipes, hoses, and cables will conduct electricity back to all equipment.

•

Low voltage current can injure or kill. Many work-related electrocutions result from contact with less
than 440 volts.

Most electric strikes are not noticeable, but indications of a strike include:

•

power outage

•

smoke

•

explosion

•

popping noises

•

arcing electricity

If any of these occur, assume an electric strike has occurred.

EMERGENCY SHUTDOWN

- Turn ignition switch to STOP.

Содержание SK750




















































































Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды

Ditch Witch SK750, Руководство оператора

Результаты поиска

Содержание SK750

Отзывы:

Похожие инструкции для SK750

Бренды по названию

Популярные бренды