manualshive.com logo in svg

Ditch Witch SK750, Руководство оператора, Страница: 16 / 83

Поделиться
Скачать
Ditch Witch SK750 Скачать руководство пользователя страница 16

SK750/SK755 Operator’s Manual

Safety - 16

Safety Alerts

CMW

Explosion possible. Serious injury or equipment damage could occur. 

Follow directions carefully.

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

Improper control function could cause death or serious injury. If control does 

not work as described in instructions, stop machine and have it serviced.

Looking into fiber optic cable could result in permanent vision damage. Do 

not look into ends of fiber optic or unidentified cable.

Pressurized fluid or air could pierce skin and cause injury or 

death. Stay away.

Runaway possible. Machine could run over you or others. Learn how to use 

all controls. Start and operate only from operator’s position.

Fire or explosion possible. Fumes could ignite and cause burns. No 

smoking, no flame, no spark.

Moving traffic - hazardous situation. Death or serious injury could result. 

Avoid moving vehicles, wear high visibility clothing, post appropriate warning signs.

Содержание SK750




















































































Отзывы:

Нет отзывов