Ditch Witch SK750 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 83

Ditch Witch SK750 Скачать руководство пользователя страница 61

Service - 61

SK750/SK755 Operator’s Manual

Startup/10 Hour

CMW

Check Hydraulic Hoses

Check hydraulic hoses for leaks at startup and
every 10 hours.

Pressurized fluid or air could pierce skin and cause injury

or death. Stay away.

To help avoid injury:

•

Before disconnecting a hydraulic line, turn engine off and operate all controls to relieve pressure.
Lower, block, or support any raised component with a hoist. Cover connection with heavy cloth and
loosen connector nut slightly to relieve residual pressure. Catch all fluid in a container.

•

Before using system, check that all connections are tight and all lines are undamaged.

•

Use a piece of cardboard or wood, rather than hands, to search for leaks.

•

Wear protective clothing, including gloves and eye protection.

•

If you are injured, seek immediate medical attention from a doctor familiar with this type of injury.

«
...
59
60
61
62
63
...
»

Содержание SK750




















































































Отзывы:

Нет отзывов