manualshive.com logo in svg

Ditch Witch SK750, Руководство оператора, Страница: 23 / 83

Поделиться
Скачать
Ditch Witch SK750 Скачать руководство пользователя страница 23

Controls - 23

SK750/SK755 Operator’s Manual

Gauges and Indicators

CMW

Item

Description

Notes

1.

Glow plug button 

To help start cold engine, turn 
ignition switch to first position.

Press glow plug button as 
directed in notes.

Release button, then turn 
ignition switch all the way 
clockwise to start. 

IMPORTANT: 

Press glow plug button 

according to temperatures below.

•

If ambient temperature is below 
40° F (4° C), press and hold 
button for 5 seconds.

•

If ambient temperature is below 
20° F (-7° C), press and hold 
button for 10 seconds.

•

Do not press button for more than 
20 seconds continuously.

2.

Engine coolant 
temperature gauge

Displays coolant temperature.

IMPORTANT: 

If temperature goes 

above 230°F (110°C):

1. Stop operation, set throttle to low 
idle, and allow engine to cool.

2. Stop engine.

3. Check coolant level.

4. Ensure radiator is clean.

3.

Engine oil pressure 
indicator

Lights when engine oil 
pressure is low.

Also lights briefly when 
engine is started.

Engine will stop.

1.  Check oil level.

2.  Check for leaks before starting
     engine.

4.

Hydraulic fluid 
temperature indicator

Lights and alarm sounds 
when hydraulic fluid is 
overheating.

Check hydraulic fluid level.

Reduce load.

Ensure oil cooler is clean.

5.

Hydraulic fluid sight 
glass

Shows level of hydraulic fluid 
in tank. Maintain fluid at 
halfway point on glass.

c00ic108h.eps

Содержание SK750




















































































Отзывы:

Нет отзывов