![Dell Z9000 Скачать руководство пользователя страница 903](http://html.mh-extra.com/html/dell/z9000/z9000_configuration-manual_84483903.webp)
LLDP Organizational TLV for Proxy Gateway
Define a new organizational TLV :
• LLDP defines an organizationally specific TLV (type 127) with an organizationally unique identifier
(0x0001E8) and organizationally defined subtype (0x01) for sending or receiving this information.
• LLDP will uses the existing infrastructure and adds the new TLV, and sends and receives only on the
configured ports.
• There are only a couple of MAC addresses for each unit to transmit so all currently active MAC
addresses are carried on the newly defined TLV.
• This TLV is recognizable only by Dell Networking devices with this feature support. Other device
ignore this field and are able to process other standard TLVs.
The LLDP organizational TLV passes local destination MAC address information to peer VLT domain
devices so they can act as the proxy gateway. Two configurations are required to enable Proxy Gateway
LLDP:
• Global proxy gateway LLDP configuration to enable this feature
• Interface proxy gateway LLDP configuration to enable/disable proxy-gateway LLDP TLV on particular
interfaces
• The interface is typically a VLT port-channel which connects to a remote VLT domain
• The new proxy gateway TLV is carried on the physical links under the port channel only
• There should be at least one link connection to each unit of the VLT domain
Following are the prerequisites for Proxy Gateway LLDP configuration:
• LLDP must be globally enabled
• No interface– level LLDP disable CLIs on the interfaces configured for proxy gateway, and you must
enable both transmission and reception
• You must connect both units of the remote VLT domain by the port channel member.
• If you connect more than one port to a unit of the remote VLT domain, it must be completed by the
time you enable the proxy gateway LLDP
• You cannot have other conflicting configurations (for example, the no static proxy gateway
configuration)
This feature might not operate properly if one of the following conditions is true:
• Any proxy gateway configuration or LLDP configuration is not working
• LLDP packets fail to reach the remote VLT domain devices (due to system down, rebooting, port
down or physical link connection)
Sample Configurations for LLDP VLT Proxy Gateway
Apply the following configurations in the Core L3 Routers C and D in the local VLT domain and C1 and D1
in the remote VLT domain:
1.
Configure
proxy-gateway lldp
in VLT Domain CONFIG mode.
VLT Proxy Gateway
903
Содержание Z9000
