![Dell Z9000 Скачать руководство пользователя страница 361](http://html.mh-extra.com/html/dell/z9000/z9000_configuration-manual_84483361.webp)
•
Assigning IP Addresses to an Interface
•
(optional)
•
Configure Static Routes for the Management Interface
For a complete listing of all commands related to IP addressing, refer to the
Dell Networking OS
Command Line Interface Reference Guide
.
Assigning IP Addresses to an Interface
Assign primary and secondary IP addresses to physical or logical (for example, [virtual local area network
[VLAN] or port channel) interfaces to enable IP communication between the system and hosts connected
to that interface.
In Dell Networking OS, you can assign one primary address and up to 255 secondary IP addresses to each
interface.
1.
Enter the keyword
interface
then the type of interface and slot/port information.
CONFIGURATION mode
interface
interface
• For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
then the slot/port
information.
• For a 40-Gigabit Ethernet interface, enter the keyword
fortyGigE
then the slot/port
information.
• For a Loopback interface, enter the keyword
loopback
then a number from 0 to 16383.
• For the Management interface on the stack-unit, enter the keyword
ManagementEthernet
then
the slot/port information. The slot range is from 0 to 1. The port range is 0.
• For a port channel interface, enter the keywords
port-channel
then a number.
• For a VLAN interface, enter the keyword
vlan
then a number from 1 to 4094.
2.
Enable the interface.
INTERFACE mode
no shutdown
3.
Configure a primary IP address and mask on the interface.
INTERFACE mode
ip address
ip-address mask
[secondary]
•
ip-address mask
: the IP address must be in dotted decimal format (A.B.C.D). The mask must
be in slash prefix-length format (/24).
•
secondary
: add the keyword
secondary
if the IP address is the interface’s backup IP address.
You can configure up to eight secondary IP addresses.
Example the
show config
Command
To view the configuration, use the
show config
command in INTERFACE mode or use the
show ip
interface
command in EXEC privilege mode, as shown in the second example.
Dell(conf-if)#show conf
!
interface TenGigabitEthernet 1/1
ip address 10.11.1.1/24
IPv4 Routing
361
Содержание Z9000
