DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 90

Страница: 90 / 192

Service Codes

TT17

Description

The Troubleshooting Tree 17 indicates an error where
the application software that was flashed to the MCU
is not compatible with the hardware configuration of
the MCU.

Note

: Refer to the MCU installation guide for more

details on installation and deinstallation procedure
including safety warning considerations.

Note

: Replace the MCU with a MCU corresponding to

the MCU subfolder specified on the Dana TM4
extranet site.

To correctly diagnose the faulty system, connect the
Diagnostic Tool (see «Diagnostics» section for test
equipment

and

descriptions)

and

the

Troubleshooting Tree procedure below.

See “Safety Warnings” and “Troubleshooting Tips”
sections for general guidelines on system diagnostics.

Related Process

The TT17 call the following process:

Appendix 6: Update Software

System Mode

Referred by SysFile ID

Condition

Possible Causes

Initialisation
(power up)

0x1003 0x3301

The application
software flashed to
the MCU is not
compatible with the
MCU hardware
configured in factory.

Wrong software flashed to the MCU

unit (not compatible with MCU P/N).

Wrong MCU P/N unit used with flashed

software.

Defective MCU (Potential wrong

factory setting).

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды