DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 49

Страница: 49 / 192

Service Codes

Refer to the

Verify Connector

Integrity

Subtree (STT01).

Is there any evidence

of an integrity loss on the VMU/

ECU interface MCU connector?

Yes

Defective MCU.

Replace MCU.

Check the auxiliary vehicle battery

contact chain (auxiliary batteries to

VMU/ECU interface harness

connector) on-board vehicle for any

intermitent contact.

Is there any intermittent

contact found on the auxiliary

batterie contact chain ( auxiliary

batteries to VMU/ECU interface

harness connector) ?

Yes

Refer to the system

troubleshooting to solve

problems.

Reconnect VMU interface

connector on the MCU.

Make sure ignition is ON.

Does the same SysFile ID

occur again?

Yes

Defective MCU.

Replace MCU.

Complete

Inspect the VMU/ECU interface

connector.

Connect to the MCU with

ODIN tool and check the

SysFile.

Switch OFF the auxiliary batteries

switch.

Switch OFF the auxiliary

batteries switch.

Switch ON the auxiliary

batteries switch.

Refer to the Dana TM4 Product installation

guide for more details on installation and

deinstallation procedure including safety

warning considerations.

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды