DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 136

Страница: 136 / 192

136

Service Codes

Is there foreign

material or DC cable shield

found near any of the DC

connection points ?

Remove the foreign

material or put away

cable shield wire from

to DC connection point.

Reinstall the DC

panel or

blankets.

Is the

problem

persists on

subsequent

Power

Yes

Is there any signs of

overheat at one or more DC

connection points that would

be caused by a loose DC

mounting screw ?

Remove the

mounting screw(s).

Reinstall the mounting

screw with appropriate

torque and put the DC cover

or blankets back.

Refer to the TM4 Product

Interface drawing for more

details on torque requirement

Is the

DC cable(s) damaged at the DC

connection point(s) ?

Replace damaged

cables.

Yes

Can the

identified

connection point(s)

(lug and DC contact point)

be cleaned without

compromising

contact

integrity ?

Clean the DC lugs and contact

points with isopropyl alcohol

using a brush.

Turn ignition

ON.

Complete

Yes

Perform a road test to check

further occurrences of the

original SysFile ID.

Yes

Wait for 10

minutes before

taking any

further action.

Defective MCU.

Replace MCU.

Ensure all High

Voltage

Electrical

sources are

switched OFF.

Switch OFF the

auxiliary batteries

switch.

Switch ON the auxiliary

batteries switch.

Yes

Refer to the TM4 Product

Interface drawing for more

details on torque

requirement

Connect to the

MCU with ODIN

to check the

SysFile.

Access the DC connection

points by removing DC

panel or blanket

Refer to the Dana

TM4 Product

installation guides for

more details on

installation and

deinstallation

procedure including

safety warning
considerations

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды