DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 164

Страница: 164 / 192

164

Service Codes

Perform a road test to check if

abnormal sound comes from

the motor.

Is an

abnormal sound

comes from the

motor

Yes

Complete

Does the same

SysFile ID occur

again?

Is the

motor resolver angle

waveform have missing

intermittent signals

evidences ?

Yes

Refer to the « Verify

Connector Integrity » Subtree

(STT01)

Is there any evidence of an

integrity loss on the motor sensor

interface connector ?

Disconnect the motor sensor

Interface connector from the

motor.

Disconnect the

motor sensor

connector at the

MCU side

Refer to the « Verify

Connector Integrity »

Subtree (STT01)

Yes

Is there any evidence of an

integrity loss on the motor sensor

interface connector ?

Investigate the

connector integrity of

the motor sensor

interface connector

on the MCU.

Investigate the connector

integrity of the motor sensor

interface connector on the motor.

Refer to the Dana TM4 Product installation guide and

operation and maintenance manual for more details on the

phase cables configurations and parameter setting

Defective MCU.

Replace MCU.

Yes

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды