DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 183

Страница: 183 / 192

183

0x120A
0x3212
0x3302

Motor not compatible with the MCU software.

Third party motor not calibrated.

Defective motor.

0x2209

0x3307

Wrong motor type connected to the MCU.

Wrong software flashed to the MCU.

Defective Motor.

0x1000

0x1100

0x1200

Defective MCU.

0x2200

Defective motor.

0x1003

0x3301

Wrong software flashed to the MCU unit (not compatible with MCU
P/N).

Wrong MCU P/N unit used with flashed software.

Defective MCU (Potential wrong factory setting).

0x3100
0x3101
0x3102
0x3103
0x3104
0x3105

Minor issue. Could potentially be raised due to internal noise under
high DC input voltage level.

Defective MCU, if 0x320D or 0x3213 SysFile ID also occurs within
the same power up.

Defective MCU, if 0x3200 to 0x3208 SysFile ID also occurs within the
same power up.

0x310A

DC high power contactor issue.

DC high power battery source issue.

DC high power battery chain connection issue (contactor, PDU, pre-
charge circuit and MCU, BMS).

Improper grounding (MCU and / or motor).

DC system load activation/deactivation.

Defective controller.

Defective MCU.

0x310B

0x310C

Significant voltage drops meaning numerous repeated connections
and reconnections (contactor or DC battery chain intermittence).

Affected motor resolver signal (motor angle waveform) that creates
DC high voltage ripple.

Resistive or bad grounding continuity between the MCU and the
motor grounding points and the chassis ground.

Another external root causes.

Defective MCU.

0x310D

0x310E

Air in the cooling circuit.

Cooling liquid flow too low or nil (cooling pump issue).

Cooling liquid temperature too high

Wrong cooling agent mixture used

– (can create dust/rust in the

cooling circuit.

Phase or DC loose contact point(s) connection(s) on MCU.

Wrong DC or phase cable crimping.

Defective MCU.

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды