DANA SPICER TM4 SUMO HP HV Powertrain Скачать руководство пользователя страница 48

Страница: 48 / 192

Service Codes

Troubleshooting Tree 04

Switch OFF the auxiliary

batteries switch.

Disconnect VMU interface

connector from the MCU.

With a mutilmeter, measure the voltage between the
following pins in the VMU/ECU interface harness
connector.

Interface connector Type 1 Interface connector Type 1

Connector pin Connector pin

Pin E or F

(Vaux +)

Pin L or M

(Vaux -)

Interface Connector Type 2 Interface Connector Type 2

Connector pin Connector pin

Pin 8 or 15

(Vaux +)

Pin 22 or 23

(Vaux -)

Is the measured

voltage >33V ?

Yes

Investigate the 12V / 24 V

board net for :

- Defective DCDC system,

- Defective auxiliary batteries.

Is there evidence

DCDC or auxiliary batteries are

causing the over voltage?

Yes

Reconnect VMU interface

connector on the MCU.

Switch ON the auxiliary

batteries switch.

Does the same SysFile ID

occur again?

Yes

Defective MCU.

Replace MCU.

Complete

Refer to the system

troubleshooting to solve

problems.

Connect to the MCU with

ODIN tool and check the

SysFile.

Switch ON the auxiliary

batteries switch.

Switch OFF the auxiliary

batteries switch.

Make sure ignition is ON.

Refer to the Dana TM4 Product installation

guide for more details on installation and

deinstallation procedure including safety

warning considerations.

Содержание SPICER TM4 SUMO HP HV Powertrain

































































































































































































Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды

DANA SPICER TM4 SUMO HP HV Powertrain, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER TM4 SUMO HP HV Powertrain

Отзывы:

Бренды по названию

Популярные бренды