Daikin BRC1E71, Инженерные данные

Страница: 36 / 46

EDUS72-975 Installation Manual
BRC1E71 35
7.2 Accessories
7.3 Remote Controller Installation Procedure
3P243521-2B
4
English
Accessories
2.
The following accessories are included.
W
ood screw
Small screw
Clamp
Operation
manual
Installation
manual
Wiring retainer
(
φ
3.5×16mm)
(M4×16mm)
(2 pcs.)
(2 pcs.)
(1 pc.)
(1 pc.)
(1 pc.)
(1 pc.)
Remote controller installation procedure
3.
Determine where to install the remote controller
.
3-1
Make sure to follow “
1. Safety Considerations
” when determining the location.
If the control cable for the remote controller is to be routed
3-2
from the rear
, make a hole in the wall taking into consideration
the location of the access hole in the lower case.
Align the center of the wall hole with the center of the access hole on the controller lower case when planning the installation.
F
5/16-3/8
External view of the remote controller
Access hole
F
5/16-3/8
Lower case Through hole
1-15/16
1-9/16
Remove upper case.
3-3
Insert a screwdriver in the recess of lower case to remove the upper case (2 points).
Upper case
Lower case
Screwdriver
Insert and twist the screwdriver lightly for removal.
Remote controller PC-board is installed on the upper case.
T
a
ke care
not to damage the PC-board with the screwdriver
.
T
a
ke care that dust or moisture does
not touch the PC-board.
If the hole size is too large or not in the proper location, it may be seen after the remote controller is installed.
NOTE
01_EN_3P243521-2B.indd 4
8/27/2009 2:00:06 PM
English
3
CAUTION
Keep water out of the remote controller
.
T
o
avoid leakage and electric shock due to entry of water or insects, fi
ll the wiring through-hole with
putty
.
Do not wash the remote controller with water as it may result in electrical shocks or fi
re.
Do not touch the remote controller buttons with wet fi
ngers.
T
ouching the buttons with wet fi
ngers can cause an electric shock.
Do not install the remote controller in the following locations:
Where a mineral oil mist or oil spray or vapor is produced, for example, in a kitchen.
(a)
Plastic parts may deteriorate and fall of
f or result in water leakage.
Where corrosive gas, such as sulfurous acid gas, is produced.
(b)
Corroding copper pipes or soldered parts may result in refrigerant leakage. Near machinery emitting electromagnetic waves.
(c)
Electromagnetic waves may disturb the operation of the control system and cause the unit to malfunction. Where fl
ammable gas may leak, where there is carbon fi
ber or ignitable dust suspensions in the
(d)
air
, or where volatile fl
ammables such as thinner or gasoline are handled.
Operating the unit in such conditions can cause a fi
re.
High temperature area or directly fl
amed point.
(e)
Heating and/or fi
re can occur
.
Moist area, where there is exposure to water
. If water enters the inside of the remote controller
,
(f)
it may cause electric shock and electrical components may fail.
NOTE
Install the control wires for the indoor and the remote controller at least 3.5 feet (1 meter) away from televisions or radios to prevent image interference or noise. Depending on the radio waves, a distance of 3.5 feet (1 meter) may not be suffi
cient to eliminate the noise.
If water enters the inside of the remote controller
, electric shock may be caused and inner
electronics may fail. When remote controller
’s
thermostat sensor is used, select the installation location as per the
following:
A
place where average temperature in the room can be detected.
Ɣ
A
place where it is not exposed to direct sunlight.
Ɣ
A
place where it is far apart from heat source.
Ɣ
A
place where it is not af
fected by outside air due to door opening/closing.
Ɣ
01_EN_3P243521-2B.indd 3
8/27/2009 2:00:06 PM