D-Link DWS-3160-24TC, Справочное руководство CLI

Страница: 96 / 983

DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
92
<value 0-65535> - Enter the TCP source port value here. This value must be between 0
and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the source port mask here.
dst_port - (Optional) Specifies that the rule will apply to a range of TCP destination ports.
<value 0-65535> - Enter the TCP destination port value here. This value must be between
0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the destination port mask here.
flag - (Optional) Specifies the TCP flag fields.
all - Specifies that all the TCP flags will be used in this configuration.
urg - Specifies that the TCP flag field will be set to 'urg'.
ack - Specifies that the TCP flag field will be set to 'ack'.
psh - Specifies that the TCP flag field will be set to 'psh'.
rst - Specifies that the TCP flag field will be set to 'rst'.
syn - Specifies that the TCP flag field will be set to 'syn'.
fin - Specifies that the TCP flag field will be set to 'fin'.
udp - Specifies to configure the UDP parameters.
src_port - (Optional) Specifies the UDP source port range.
<value 0-65535> - Enter the UDP source port value here. This value must be between 0
and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the source port mask here,
dst_port - (Optional) Specifies the UDP destination port range.
<value 0-65535> - Enter the UDP destination port value here. This value must be between
0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the destination port mask here.
protocol_id - Specifies that the rule will apply to the value of IP protocol ID traffic.
<value 0-255> - Enter the protocol ID used here.
user_define - (Optional) Specifies that the rule will apply to the IP protocol ID and that the mask
options behind the IP header , which has a length of 20 bytes.
<hex 0x0-0xffffffff> - Enter the user-defined mask value here.
mask - Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffffffff> - Enter the mask value here.
packet_content - A maximum of 11 offsets can be specified. Each offset defines 2 bytes of data
which is identified as a single UDF field. The offset reference is also configurable. It can be
defined to start at the end of the tag, the end of the ether type or the end of the IP header. To
qualify the fields before the end of the tag, the destination address, source address, and the
VLAN tags are also included
offset_chunk_1 – (Optional) Specifies the value of the packet bytes to be matched. Offset
chunk 1 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 1 mask here.
offset_chunk_2 - (Optional) Specifies the value of the packet bytes to be matched. Offset
chunk 2 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 2 mask here.
offset_chunk_3 - (Optional) Specifies the value of the packet bytes to be matched. Offset
chunk 3 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 3 mask here.
offset_chunk_4 - (Optional) Specifies the value of the packet bytes to be matched. Offset
chunk 4 will be used.
<hex 0x0-0xffffffff> - Enter the offset chunk 4 mask here.
ipv6 - Specifies that the rule applies to IPv6 fields.
class - (Optional) Specifies the value of the IPv6 class.
<value 0-255> - Enter the IPv6 class value here. This value must be between 0 and 255.
flowlabel - (Optional) Specifies the value of the IPv6 flow label.
<hex 0x0-0xffff> - Enter the IPv6 flow label mask used here.
source_ipv6 - (Optional) Specifies the value of the IPv6 source address.
<ipv6addr> - Enter the source IPv6 address used for this configuration here.