CYPRES 2 Скачать руководство пользователя страница 25

Страница: 25 / 72

- CYPRES 2 User’s Guide -

page 25

wait!

click

wait!

click

self-test and

calibration

unit

switched on

click

light

appears

light

appears

light

appears

4.2 Switching CYPRES on

CYPRES is switched on by pressing the button

(pushbutton switch) four times with very short

clicks. Start the switch-on cycle by clicking the

button once. After approx. one second, the red

LED-light will glow. You must acknowledge the

red light immediately by clicking the button again.

This sequence - a click following appearance of

the red light - will be repeated two more times.

After a total of four clicks, CYPRES goes into

self-test mode.

If you do not act promptly after seeing the LED-

light, or if you push the button too soon, CYPRES

will ignore the switch-on attempt.

This four-click initiation cycle has been designed

to avoid accidental switch-on.

Once the switch-on procedure is finished, the unit

will run through its

self-test. Initially, the

display

will show the number

, and then a count-

down ending in

. When the

with

the arrow down is shown, the unit should be func-

tional for the next 14 hours. After 14 hours have

passed, the unit will switch itself off automatically.

A manual switch-off is always possible using the

button. If the

self-test is not successful, an error

code is shown for approximately 2 seconds. The

meaning of this error code can be seen in chapter 5.

The manual switch-off sequence is the same as

the switch-on procedure (click, light, click, light,

click, light, click). This routine is designed to avoid

accidental switch-off.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды