CYPRES 2 Скачать руководство пользователя страница 40

Страница: 40 / 72

page 40

- CYPRES 2 User’s Guide -

Notes:

1. CYPRES 1

field replaceable

cutters (no alumi-

num grip) can be used with CYPRES 2 They

will function properly, however this combination

is not water-resistant.

CYPRES 2 cutters (identified by aluminum

grip) can be used with any CYPRES 1 with the

field replaceable cutter connector. They function

properly - but this combination is not water-

resistant.

2. Release units (cutters) are numbered via a heat

shrink tubing placed on the cable. This number

identifies the cutter. A table of cutter numbers with

corresponding dates of manufacture are available

at www.cypres.cc

3. It is possible that the cutter plug could separate

from the socket after a CYPRES activation. In

the rare combination of this and a water landing,

the socket must be dried out before further use.

Do that by tapping the open end of the socket

flat onto a flat surface such as a table top. Once

no additional water comes out while tapping on

the table top, store the CYPRES with the open

end of the socket hanging downward for another

24 hours in a dry area, to allow the socket to dry

out completely. When completely dry, insert the

plug of the new cutter.

4. Use a one-pin cutter in a one-pin container and

a two-pin cutter in a two-pin container.

Do not use release units (cutters) after the end of cutter

service life (16,5 years after DOM)

Used release units (cutters) that are / were attached to

a CYPRES unit are also subject to a technical service /

maintenance. See chapter 14.1.

New release units (cutters) that were never attached

to a CYPRES unit and were stored (according to

manufacturers instructions) do NOT need to be send in

for maintenance within the service time frame.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды