CYPRES 2 Скачать руководство пользователя страница 45

Страница: 45 / 72

- CYPRES 2 User’s Guide -

page 45

choice of their users. Please avoid that.

When descending with WSC users on board, do

not exceed 3500 feet/min vertical below 2000 feet.

1500 ft

NO !

1500 ft

Flight limitations:

• Never fly below the airfield takeoff elevation

•

Always go above 1500 feet (450 meters), for

Tandems 3000 feet ( 900 meters)

• If dropzone offset has been adjusted, never fly

below the intended DZ elevation

Not respecting the limitations can cause injury or death.

max airspeed, and typical aircraft VSI instruments

are heavily damped and “peg” at 3,000 ft./minute.

Note: in the case of Student CYPRES, always

make sure the jumpmaster has switched them off

prior to descent in ANY aircraft.
Note: in the case of WSC on board:

Once you have overflown 2000 feet and thereafter

descent with less than approx. 8,5 m/s but more

than 2.5 m/s for more than 10 seconds (may vary

on user’s settings) in the range of between approx.

6500 feet and approx. 1500 feet above the ground

and have WSC users on board you might trigger

their units to change from Wing Suit Status to

Canopy Status. That does not apply for the first

500 feet which you descend. Only if you descend

more than 500 feet, then it may apply. In

case it happens the additional Wing Suit

Status of their units is not active on

that one jump. The

units behave like

an Expert or like a

Speed CYPRES, depending on the

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды