CYPRES 2 Скачать руководство пользователя страница 22

Страница: 22 / 72

page 22

- CYPRES 2 User’s Guide -

tions of the different harness/container systems,

should not create any negative influence on the

original function of the CYPRES unit, which is

the cutting of the reserve closing loop. It had to

be assured that the initiation of the reserve open-

ing (severing the closing loop) did not hinder the

reserve development in any way.

All CYPRES installations should be performed and

approved by the harness/container manufacturer in

collaboration with the AAD manufacturer.

Should you wish to install a CYPRES into a con-

tainer which does not have a CYPRES set-up, you

should contact the harness/container manufacturer

for advice and instructions.

3. Installation

During the first years after introduction of the

CYPRES AAD it was necessary to establish a

testing and evaluation procedure for the installa-

tion of this new AAD into the existing harness/

container systems,

as there was no such

AAD concept on the

market.

The installation had

to be tested and ap-

proved. This was

solely done at Airtec

GmbH & Co. KG in

Germany until 2012.

Airtec GmbH & Co.

KG undertook this

task in preference to

the harness/container

manufacturers to find out the best and safest pos

sible installation for each system.

The resulting installation instructions, in all it´s

variations, originated from the different construc-

„Each parachute manufacturer

approves the installation of the AAD

on their equipment.“

12/04/13 AC No:105-2E Page 4 part 2.b.

of Advisory Circular of U.S. Department of Transportation, Federal

Aviation Administration

Retrofit:

Comply with the specific retrofit instructions of

the harness/container manufacturers.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды