CYPRES 2 Скачать руководство пользователя страница 55

Страница: 55 / 72

- CYPRES 2 User’s Guide -

page 55

Standard settings for Wing Suit CYPRES (WSC):

Cable length of control unit: ..... approx. 650 mm

Volume: ..................................... approx. 139 cm³

Weight: ...................................approx. 198 grams

Dropzone offset adjustment limits: ............................

.................................................±1050 feet or ±350 m
Wing Suit Status:

Activation altitude: ........... approx. 750 - 130 feet

Activation speed: .....approx. > 45 mph (20 m/s)
Canopy Status:

Activation altitude: .........according to set MODE

Activation speed: ...........according to set MODE
Status change:

•

between approx. 6500 feet (2000 meters) and

approx. 1500 feet (450 meters) above ground,

•

when descending

less than approx. 19 mph (8.5 m/s), but more

than approx. 5.6 mph (2.5 m/s)

for 6-20 seconds depending on where this

status change time is programmed.

Default status change time ................10 seconds

14.1 Versioning

For units with DOM 12/15 and earlier the

maintenance is mandatory to be performed

4 and 8 years after the original DOM.

Service Life is 12.5 years.
For units made in 2016 the maintenance is recom-

mended to be performed 4 and 8 years after original

DOM. Service Life is 12.5 years.
For units with DOM 01/17 and later the main-

tenance is recommended to be performed 5 and

10 years after the original DOM. Service Life is

15.5 years.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды