CYPRES 2 Скачать руководство пользователя страница 38

Страница: 38 / 72

page 38

- CYPRES 2 User’s Guide -

5. Error Display

If there is an error condition detected during the

self-test countdown, CYPRES 2 shows an error

code on the display for approx. 2 seconds, then it

switches itself off. (Display goes blank).

Error code number / error code description:

: One or both of the attached re-

lease units are not correctly electrically connected

to the unit. The reason may be a cable break, the

cutter plug could be disconnected, or the release

unit(s) may have activated.

: Excessive variations in ambient air

pressure have been measured during the self-test

period. The unit is unable to obtain consistent

values for the ambient air pressure at ground level.

Possible reasons could be that an attempt to switch

CYPRES on has been made in a car driving uphill

or downhill, in an elevator or in a flying aircraft.

The switch-on procedure can be performed several

times after a

error was displayed. If

is displayed, the unit has successfully gone through

the self-test.

Additional error codes for units produced / serviced

on or after January 2013.

Power Down
Checksum Error
Pressure Sensor Error

After one of these three error codes appears, the unit

switches off and cannot be switched on again. Please

discontinue use and send the unit in for service. If

other error codes appear in the display, if the unit

switches itself off and can not be switched on again,

if the unit does not switch off after 14 hours, if there

is no red light when the button is pressed, or if

anything else unusual occurs please record the error

code and contact Airtec or SSK before further use!

Malfunction: A malfunction can easily injure or kill

you or others.

Every technical device can fail. So everything imaginable

can happen with the CYPRES, including, but not limited

to: displaying a status which is not true, failing to function,

or functioning at a wrong moment or at a wrong occasion.

If you or your friends or family are not willing to accept

these uncertainties and risks, then you must not use

CYPRES.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды