CYPRES 2 Скачать руководство пользователя страница 21

Страница: 21 / 72

- CYPRES 2 User’s Guide -

page 21

CYPRES (depending on your choice) throughout

only this one jump.
Additional remarks:

The Wing Suit Status activation speed is 45 mph

(20 m/s) vertical. If that speed is exceeded at an

altitude of approx. 750 feet above the ground then

an activation should happen. That criteria should

arrange that in case you are unconscious and fly

with your wing suit towards the ground the WSC

initiates your reserve parachute.

At the WSC the dropzone offset adjustment is

limited to ± 1050 feet or ± 350 meter.

Have you heard about Sky Surfing?

Jumps with a Surf Board create similar physical

conditions as jumps with a Wing Suit.

The WSC can also handle the Sky Surf discipline.

* Patent Pending

** The criteria for the Status change is: descending

with less than 19 mph (8.5 m/s) but more than 5.6 mph

(2.5 m/s)for a duration of 10 seconds (default value)

between approx. 6500 feet (2000 meters) and approx

1500 feet (450 meters) above the ground.

*** If you have programed a user-selectable activation

altitude, then you have to increase the 1500 feet by the

programed value.

Maintenance / Repair / Service:

The Audio and the cutter should be sent in together

with the WSC unit.
For Jump pilots:

Once you have overflown 2000 feet and thereafter

descend with less than approx. 8.5 m/s but more

than 2.5 m/s for more than 10 seconds in the range

of between approx. 6500 feet and approx. 1500 feet

above the ground and have WSC users on board

you might trigger their units to switch from Wing

Suit Status to Canopy Status. That does not apply

for the first 500 feet which you descend. Only if

you descend more than 500 feet, then it may apply.

In case it happens then the additional Wing Suit

Status of their units is not active on that one jump.

The units behave like an Expert or like a Speed

CYPRES, depending on the choice of their users.

Please avoid that.

When descending with WSC users on board, do

not exceed 3500 feet/min vertical below 2000 feet.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды