CYPRES 2 Скачать руководство пользователя страница 57

Страница: 57 / 72

- CYPRES 2 User’s Guide -

page 57

16. Disclaimer

In designing and manufacturing CYPRES, the aim

of Airtec GmbH & Co. KG Safety Systems, is that

the device should not accidentally sever the loop but

should try to sever the reserve closing loop when

the activation criteria are met.

All investigations and experiments performed dur-

ing the product‘s development and all laboratory and

field tests accompanying trial and production phases

have indicated that CYPRES meets both these goals.

However, as an electro-mechanical device the pos-

sibility of CYPRES malfunctioning cannot be ex-

cluded. Such may cause injuries or death. We accept

no responsibility for damages and consequences

resulting from any malfunction.

Airtec GmbH & Co. KG Safety Systems also ac-

cepts no responsibility for damages or problems

which are caused by the use of non-original Airtec

parts and supplies.

The use of CYPRES is voluntary, and does not

automatically prevent injury or death. Risk can be

reduced by assuring that each component has been

installed in strict compliance with the manufac-

turer‘s instructions, by obtaining proper instruction

in the use of this system, and by operating each

component of the system in strict compliance with

this User‘s Guide.

If used in the United States, the use of CYPRES

shall be in accordance with USPA BSRs.

Automatic activation devices (AADs) sometimes

display a wrong status, fail to operate or operate

properly, and sometimes activate when they should

not, even when properly installed and operated.

Therefore the user risks serious injury or even death

to themselves and others during each use.

By using or allowing others to use CYPRES, you

acknowledge that you accept responsibility for the

proper use of the device, as well as accepting the

consequences of any and all use of this device.

Airtec GmbH & Co. KG Safety Systems, their Deal-

ers, Service Centers, and Agents total and complete

responsibility is limited to the repair or replacement

of any defective device.

CYPRES is strictly a backup device, and is not

intended to replace proper training or timely execu-

tion of appropriate emergency procedures. If you,

your friends, or family are not in agreement of these

disclaimers please do not use CYPRES. Please note

that even though CYPRES has an extraordinary

track record, your results may vary.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды