CYPRES 2 Скачать руководство пользователя страница 37

Страница: 37 / 72

- CYPRES 2 User’s Guide -

page 37

4.7 Changing the

filter

Filter Removal:

Hold the CYPRES

filter changer

on the non-slotted end and push it straight (without

tilting) onto the filter up to the stop position.

Tightly grip the filter

changer, twist off by turn-

ing in a counterclockwise

direction and remove the

filter. If there is water in

the casing (behind the

filter), thoroughly dry

it with an absorbent soft cloth. Remove the old

filter from the filter changer by pushing with your

finger or with the eraser end of a pencil. Discard it.

Filter Installation:

Place the new filter with the

labeled side toward and into the slotted end of

the filter changer up to the stop (flush) position.

Do not angle.

Hold the filter changer by the non-slotted end,

gently slide the filter fitting into the unit holding

it straight without tilting. Turn the filter changer

clockwise, initially there will be little resistance.

Continue turning the filter changer until it slips on

the filter. (The filter stops turning but the changer

continues to turn.) Remove the filter changer from

the filter by pulling

straight back.

Do not use other tools!

The unit must be switched off

before filter change.

Содержание 2









































































Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды

CYPRES 2, Руководство пользователя

Результаты поиска

Содержание 2

Отзывы:

Похожие инструкции для 2

Бренды по названию

Популярные бренды