Curtiss-Wright EXLAR Tritex II AC Скачать руководство пользователя страница 61

Страница: 61 / 89

Curtiss-Wright | Tritex II AC 90, 115 Rev. X PN39892 7/12/22

I/O Power Supply

In order to use Digital Outputs, an external 24Vdc nominal power

supply connected with positive side to one of the Field I/O + terminals

and negative side to one of the Field I/O Common terminals on the

Terminal Board. Typically terminals J2-1 and J2-2 are used for this

purpose. For connector option I, refer to the preceding table for pin

usage. The negative side of this power supply should be tied to PE near

the power supply. As with the Control Logic Supply, a fuse is necessary

unless power supply self-limits at 3A or less. The fuse should be rated

2A or less, depending on load and placed in the positive side.

Digital Inputs are typically powered from the same supply externally

through the contact or sourcing output providing the signal, but the only

requirement is that the supplies for Digital Outputs and all Digital Inputs

have the negative sides connected.

The same supply may be used for control logic power by installing

jumper wires from J2-9 to power terminal C+ and from J2-10 to power

terminal C-. The same power supply can also provide power for the

optional holding brake; option RB, by installing a jumper wire from J2-11

to J2-12. This jumper is factory installed with connector option I if a

holding brake is also present. A 2A fuse is necessary if the supply is

used for Control Logic or a brake.

For UL applications, the I/O power supply must be a UL recognized or

listed Class 2 power supply and shall be marked “Class 2” next to the

voltage rating of the device.

For applications to meet the CE Low Voltage Directive an approved

24V supply must be used and the negative side must be grounded to PE.

Actuator View

Cable View

Содержание EXLAR Tritex II AC


























































































Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды

Curtiss-Wright EXLAR Tritex II AC, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EXLAR Tritex II AC

Отзывы:

Похожие инструкции для EXLAR Tritex II AC

Бренды по названию

Популярные бренды